To stream full HD videos on the internet, you must have a secure and high-speed internet connection at your home. Imagine watching your favorite movie with your loved ones and keep on buffering from time to time; all your excitement goes in vain. To prevent misadventure, ethernet connections are made, providing you with enhanced internet speed.
Wiring your home with ethernet cabling, you can easily install a gigabit network and enjoy the fastest speed of the internet. But on the other hand, wiring a home doesn’t seem to be easy for most homeowners. Turns out, the house looks more like a big data center with cables running all around.
However, if you use your mind and know how to run ethernet cables through walls, you can still get the fastest internet speed without creating a mesh in your house. If you don’t know how to do it, there is nothing to be worried about, as you will know all about it here in this blog.
Remember that setting up ethernet cables is preferred when a house is built, as it is going to be easy. But, if this is not done during the construction, you can still run ethernet cable through walls, and for that, you need to know the correct procedure.
So, let’s get right into the steps, run ethernet cable through walls and enjoy the high-speed internet.
Preparation
No matter what kind of work you are going to do, it is always better to prepare for it beforehand. In this case, by preparing means, you have decided the location and route for the wiring. Other than that, you must have gathered the appropriate tools such as for drilling holes or cutting wires. Once you are done preparing, it’s time to get on the job. It might seem difficult, but with the right steps, you can do this perfectly. Let’s find out what’s next?
Choose a place
As part of the preparation plan, it is so much emphasized because if you are not able to decide a way to run cable through, you won’t be able to proceed any further. You might have to drill some holes through walls to let the cable pass-through, keeping in mind that you are not damaging the electrical or plumbing system. It is therefore suggested that you use a wall scanner to make sure there are no plumbing or electrical lines running through the wall.
Besides that, choose the location that is out of the way so there are no disturbances afterward.
Position the wiring panel
A wiring panel or a box is where all your wires connect and spread into your house. It should be in a central position so that ethernet cables can be routed easily. Usually, you will find this box in the basement of your house, but it’s not always necessary.
Choose the appropriate cable
If you have been into this before, you would know that there are different types of ethernet cables available. Specific to the internet speed requirements, you must know your requirements before anything else.
Draw up a wiring plan
Once you have finalized the location, it is good to have a wiring plan in your hand. At this stage, you can actually set up a route, decide where to place the router, and how many rooms need to have a cable hookup. After devising a wiring plan, you can inspect it again and make necessary changes if required. This will help you come up with the perfect plan with no mistakes.
Drill holes for ethernet cables
As now you know the exact route of the ethernet cable, start drilling holes where required. Drilling does not require much expertise, but if you have not done this before, it is better that you call a friend for help.
Before you do the drilling, there is a way that will allow you to run ethernet cables in an organized way. That is, by using a structured wiring panel. By using these panels, wires won’t be hanging on the walls. It will just improve the outlook and help in better organization.
Run wires through the walls
It’s finally time for setting up and running the cables through walls. Run the wires through the drilled holes and put them through the route as you have planned in the wiring plan. For ethernet cables, you must be careful as twisting or bending these cables may affect the performance.
Label the wires so that you know where it is destined for. Run cables through each room you have specified and let it go. To make it secure, do not use the staple as it can damage the wires; instead, use the fishing tape.
Pull each cable out of the holes and use them as you desire. Do not forget to seal the drilled holes once you are done feeding the ethernet cables.
Conclusion
This may not be a one-person task, but with the help of a friend, it is definitely something that you can try yourself. From deciding a location to feeding the wires through holes, all you need to know are the right steps and a bit of patience. Once you start, you will end up finishing the task in one go. Do you feel like replacing the ethernet cables of your house? Well, you know the strategy now.